焊接專機設備操作規范參考信息
來源：http://maxsenz.com/ 發布時間：2022-11-26 瀏覽次數：0
今天山東焊接專機小編來跟大家聊聊焊接專機焊接機操作過程中有哪些需要注意的事項，希望對大家能有所幫助。
Today, the small editor of Shandong Welding Machine came to talk with you about what should be paid attention to during the operation of the welding machine of the welding machine. I hope it can help you.
1.設備主機及焊接頭外觀注意防塵。
1. Pay attention to dust-proof appearance of equipment host and welding joint.
2.水機兩側勿堆放雜物并保持1米空間以保證通風制冷。
2. Do not stack sundries on both sides of the water machine and keep a space of 1m to ensure ventilation and refrigeration.
3.每日早班時先檢查焊接頭保護鏡片，再開機開氣。
3. Check the protective lens of the welding head at the morning shift every day, and then turn on the machine to open the air.
(檢察時保護鏡抽屜拉出一半能看到鏡片中間位置即可)
(During inspection, pull out the protective mirror drawer half to see the middle of the lens)
4.焊接過程中若出現能量減弱現像，應立即停機并檢查保護鏡片，檢查方法同上。如有黑色燒點及時更換。
4. In case of energy loss during welding, stop the machine immediately and check the protective lens. The inspection method is the same as above. If there are black burning spots, replace them in time.
5.更換保護鏡片時注意事項
5. Precautions when replacing protective lenses
①先關閉焊接頭附近所有吹氣，吹風設備。減少空氣流動。
① First, close all air blowing and air blowing equipment near the welding head. Reduce air flow.
②用無塵布蘸酒精或丙酮將保護鏡抽屜周邊擦拭干凈。
② Wipe the perimeter of the protective mirror drawer with a dust-free cloth dipped in alcohol or acetone.
③取下保護鏡抽屜后，應立即用美紋紙將保護鏡抽屜窗口封住，防止灰塵進入焊接頭內。
③ After the protective mirror drawer is removed, the window of the protective mirror drawer shall be immediately sealed with masking paper to prevent dust from entering the welding joint.
④更換保護鏡片時，不能接觸鏡片表面應捏住鏡片側邊。
④ When replacing the protective lens, the side of the lens should be pinched if the lens surface cannot be contacted.
⑤換好鏡片后，用吹氣球吹去表面浮塵。
⑤ After changing the lens, blow the floating dust off the surface with a blowing balloon.
⑥取下封口美紋紙，按正確方向?qū)⒈Ｗo(hù)鏡抽屜裝回。
⑥ Remove the sealing paper and replace the protective mirror drawer in the correct direction.
6、焊接應盡量減少焊接煙塵，若煙塵過多，需配備抽塵沒備將煙塵抽走。
6. Welding fume shall be reduced as much as possible. If there is too much fume, it is necessary to provide dust extraction to remove the fume.
為了保障您的人身以及延長設備的使用壽命，請熟知以上操作，如有問題請聯系我們http://maxsenz.com咨詢！
In order to ensure your personal safety and prolong the service life of the equipment, please be familiar with the above safe operations. If you have any questions, please contact us http://maxsenz.com consulting service
上一篇：焊接變位機送絲裝置的保養方法
下一篇：自動焊接設備可以焊接哪些工件
